There is a hole in the bottom timber section of double garage door. My husband has taken a look and the wood does not seem to be rotten. We need someone to offer some advice and let us know whether repairs are even possible and how much it cost. The garage door would be at my son's house in Fourways.
1 Standard Double Sectional Automated lift door with draughtproofing. The existing Double is of the 40 raised panel type single up and over and will remain in place until all new brickwork is completed 3 mtrs forward of existing door and new door to be fitted before removal of the old door. This is for security reasons. This installation/removal is subject to planning approval and completion of new brickwork and roofing not earlier than September/October time.
Good day. Can I kindly request a quote. I want to close my patio with either sliding doors or stackable doors depending on affordability. Main door = 6m wide X 2.5m high. Second opening = 1.7m wide X 2.5m high Third opening = 1.5m wide X 2.5m There are two existing sliding doors which I'd like to remove and reuse if possible, their measurements are as follows; 2.4m wide X 2.1m high 1.8m wide X 2.1m high I understand that the final quote will be based on final measurements but I'm seeking an estimate for now. Please quote me and advise with regards to alternative options as I am not fixed with heights. If the 2.1m heights are more feasible, then I'll be happy to install block windows above the doors. The two sides of the patio do not need to be accessible.
The measurements (4 options) I need for the sliding doors are: 3m (L) x 4.5m (w) left and 4.5m (w) 2.8m (L) x 4.5m (w) left x 4.5m (w) right 3m (L) x 4m (w) left x 4m (w) right 2.8m (L) x 4m (w) left x 4m (w)right Please note that the sliding doors will have a pocket in the wall where they stack into when opened. The floor track preferably recessed. The measurements are for doors that meet at a corner 90 degree opening. They can stack separately on either side.
I've got a single door garage door which the installer bought from Doorman Vredenburg. The top part was not stable from beginning, the installer told me it was a factory fault and he will replace it for me. To make a long story short, he disappeared along with the Doorman agent in Vredenburg. I need a quote for the top part and somebody to replace it for me.
I currently do have garage doors and carports in front of the garages. My cars do not fit into the garages anymore and are currently standing under the carports but I have big dogs who are not moving between the cars and damaging them so I need some advice on what to do. I will only be available for a site inspection after 17:00
Good day, Please help with a quote for the doors below with installation. Should the sizes need to adjust a little to get standard doots that are cheaper then this is fine as well as we still need to break the walls. All of them should be black aluminium. Sitkamer - 4.5 x 2.4 Sitkamer 2 - 4 x 2.4 Sitkamer 2 kant - 4 x 2.4 Stoep - 4 x 2.4 Kids stoep - 4.5 x 2.4 Regards,
Good day, i just to find out if you do automative Garage doors with the current door or do you recommend putting in a new door with the automatic system. The size is 4.84 (width) x 2.80 (height). Please let me know. We are desperately looking for an automatic door, because this door we have to push up and pull down and the door is very heavy. Hope to hear from you soon. Kind Regards
Please message me on Whatsapp. I will be able to respond there during work hours. Old doors that flip up and when up are half-in, half-out. Currently wooden, want to replace with something better quality and automated. Also a “garage door” that is behind the gate, blocking a view of the driveway - same mechanism and door type as the garage door. I want that driveway gate and both garage door gates replaced and automated.
I currently have 2 separate doors outomated with one centered Gemini motor. The current roll-up steel doors are old and grinding it out every time we open it. The doors either have to be replaced with 2 new doors, or have to be replaced with one solid door with a new motor. The current motor is however fine. I need advice and a quote to take an informed decision to make a change-over. Uncertain ito steel or alluminium and price/quality difference. Please contact me.