What kind of permissions do I need for my electric fence, and where to get them?
Electrical fences are dangerous, so you need to obtain permission before installing them. What are they? Where do you get them?
Services: Pool fence, Garage doors, Wooden garage doors, Wood fence, Palisade gates, Steel garage doors, Electrical contractors, Sliding driveway gate, Garden fence, Roller garage doors, Gates, Metal gates, Concrete fence, Security gates, Automatic garage doors, Handymen, Glass garage doors, Swing gate, Electricians, Electric fence, Aluminium garage doors, Wire mesh fence, Electrical repair, Plastic fencing, Palisade fencing, Sliding security gate, Roll up garage doors, Turnstile gate, Emergency electrician
One 6,4 meter gate. More or less One 2.7 meter. More or less. The two gates must meet. The long gate must be in front of the garage doors. Then other gate can be pushed open . We have a caravan that must be able to pass through the small gate. The attachment between the two gates must be able to go down when taking out the caravan.
contractor that will be able to remove the existing fence and install a new Steel Palisade fence at the Tsheesebe Primary School in Waterberg District Municipality 3. STEEL PALISADE FENCE AND ACCESSORIES SPECIFICATIONS 3.1. Installation of Steel Palisade Fencing Panels: 1.8 x 3m above ground level. 3.2. Fence bearers: 40 x 40 x 2m angle iron. These are to be placed mm from top of paling and mm from bottom of paling. (mm from ground level). These are to be welded flash with the back of the post. 3.3. Palings “Devil Fork” 21 palings per panel. 30 x 30 x 2mm steel angle iron paling 1.8m high. Paling to be inserted and firmly welded to the bearers at mm centres to be centre. Top of the paling to provide a “Devil Fork” effect and bottom will have a dove tail. 3.4. Installation of 2.4m high (76 x 76 x2 mm) Posts: 76 x 76 x 2mm steel square tubing with closing pyramid caps on top. Post must be 2.4m high and mm will be planted into concrete footing to Engineer’s design. 3.5. Installation of Palisade Gates for Pedestrian and Sliding Gate 3.5.1. Sliding Gate: 5 m wide x 1.8 m high. 40 x 40 x 2 mm 4 m wide x 1.8 m high. 40 x 40 x 2 mm Post to be founded in a concrete footing x x deep. Concrete strength to be 20Mpa (minimum) at 28 days. 3.5.2. Pedestrian gate: 1.2 m wide x 1.8 m high. 40 x 40 x 2 mm 3.5.3. Painting: Clean surface and allow to dry completely. Remove all Flux, Rust, Grease and loose material before painting. All joints must be smoothed. Apply one coat Primer for steel (red oxide) and apply one coat universal undercoat and one coat Gloss Enamel (Traffic Green as specified by the LPDE) No brush painting. 3.5.4. The School has perimeter of metres N.B. the tenderer must price for Installation Labour Only, Including the concrete footing; the fence will be supplied by the fabricators.
Good morning Can you please send me a quote for 4 x 2.4M x 3 M x 20 PALES PER 3 METER /SPIKES=SPEAR 30 X 30 COLDROLL ANGLE panels 1 x 2.4M x 1 M Panels 6 x 3M x 76x76 x 1.6 POST 1 x 0.9 x76x38 Rectangular Tube 1.6 Pedestrian Gate And nut and bolt for mounted all panels mounted to the post Area will be 4M x 3M Am looking for your reply
Hello, I'd like a quotation to install an electric fence on my property. We're sub-dividing a plot in Farmall, so there is an existing perimeter fence, but we'd like to define a new boundary within that with approximately ~m of 18 strand fence connected to the existing boundary. The existing boundary fence (~m) needs a new energizer and possibly some repair. Sketch attached with existing boundary (red); new fence (green); and location of energizer (red circle). Please contact me by email. Regards,
Move an existing db board in a house To a position 6m away so a wall can be broken down So cut metal conduit in the ceiling extend the existing 2.5cm and 16mm cables by 6m Put in trunking and reroute to new position Mount new plastic db box Move all breakers earth leakage etc from old board to new board
I am looking for fencing for my yard, for a farmland. I am able to arrange pick-up from the supplier. I would also like some advice with regards to how many poles will be needed along with the fencing and with regards to anything else I might need along with the fence. I would also like to know the difference in costing between supply of fencing materials only and supply + installation.
I require 3 electrical companies with the correct certificates and licence to operate and service level agreements with insurance to join my team. You must be able to be available to work 24hrs should we have an after hour issue. Should you be interested please EMAIL me no CALLS to I will arrange a meet with you after I go through your qualifications. building is a 20 story building with units. Kind regards Maintenance & Building Manager
To razor wire a small weak access area on property. Dogs prove a good deterrent as do the sheer height and fencing/security by neighbouring properties. Due to constant Load Shedding, camera, electric fence and security options prove redundant due to their reliance on electricity. As such, I would like to just address the small weak area. Not a very big job but necessary so a visit and subsequent quote would be most appreciated.
I need rstimayed quotes electrical compliance for two properties . Include in property 2 the repair of trip switches and 2 plugs in kitchen and 2 faulty lightfittings with possible wiring problems. 1) House in complex . 3 bedrooms lounge dining room kitchen 2 bathrooms garage. 2) 2 bedroomed semi detached house in complex with 1 bathroom kitchen lounge dining area. Urgent please.
Hi. Recently bought a house and there's no wiring or DB board. There are outlet points but no outlet, no light switches and no lights (there are holes for the plugs and switches already) It is a 3 room house and a granny flat at the back that has a small kitchen and bedroom and bathroom. Need quote for the house and for the single flat (need 3 separate quotes, house, flat, house and flat)