We need advice on what needs to be done to obtain a COC. It is a farm / rural/ setting. We then need a COC to be issued when compliant as well, We were also advised to rather remove unnecessary items like pumps for water fountains, "pretty stoep lights" and self installed leads etc. The are three Eskom low amp boxes on the property that feeds each building
we have been renovating some of the house over the last couple of years, but we are looking to upgrade so that we can sell the house for more. upgrading includes a full renovation of the kitchen and scullery area, upgrading two bathrooms, replacing all the window frames and flooring, skirtings, fireplace, painting and stiling the 5 bedroom house.
Good day Sir / Madam I trust this email finds you well. We are kindly requesting you guys come and do a site inspection at 90 Bekker Road, Vorna Valley Building A, Hertford Office Park, Midrand ( Do advise when you can come through) on the following request, • 5 Red plugs with 5 external multiplugs • The plugs must be round on the LIVE POINT ( not a half hole please ) • The plugs will be mounted on the poles and external multiplugs can be connected externally there ( picture attached ) The quote must include the following: • Labour rates ( For after-hours) • Show us a consumable explanation of the reg plugs in terms of power usage • installation costs (Including Cabling on walls and desk to the Genset)
plumbing a bathroom needs to be done over as it is an old steel bath where plumbing is not in wall but on the wall. tiles also need to be replaced. it will be a bath with a shower overhead, basin also be replaced. garage roof also needs to be done over the wooden strip on wall against which sheeting is mounted is rotting badly so whole roof needs to be done with most of the frame still being in excellent condition. poor waterproofing caused the rot. one face board on the main home also needs to be replaced. possibly would like the wall in front of home removed and replaced with solid sliding steel gate as well. this gate will be manual not motor based
I want to build a 20 unit apartment complex with 10 one bedroom unit and 10 two bedroom units. It must include a large swimming pool, under cover parking/protective parking. Have a reception office near the entrance of the complex. Security office at the gate. A convenient store in the complex and a pre-school.
It's a small room about 2.7m x 3.2m that requires remodelling for the use of a Tanning/collogan Studio. Work required: *Need the existing window replaced with a door to enable access from outside. *Old aircon removed and wall filled *flooring *lighting *electrical works (including surge protection) *dry wall partition *solar or generator installation
It is a double story renovation from rental to a bed and breakfast. There is four to 5 plugs per room, every room has an en-suite bath/shower. It is 11 bedrooms, kitchen, dining area, Reception area, 2x linen rooms, each floor has its own DB, earthing required, outside lights working with a day/night switch, 2x geysers, 1 stove
I need to redo a bedroom into an office and lounge space. I would need the removal of old doors to be replaced with new doors and the removal of cupboard doors and replacement with new. The skirting of the room needs to be sanded and old paint on them removed and restained. Walls need to be painted including accent walls. Built in cupboard needs to be redone. Shelving needs to be designed and installed.
We are moving into a rented house, which we may decide to buy and renovate later. Initially we would like a quote for doing some restoration/repair work and a thorough repainting of the main downstairs rooms as well as the 3 bedrooms upstairs - we will have occupancy from 1st of Feb but will be allowed access before that to complete the work. If the work is good quality, you would be considered for the larger renovation once the property is purchased. Thanks,
1) To remove the retainer blocks in question against the precast fence between units 2 and 3. 2) To excavate and pour a 25 MPA concrete foundation. 3) To construct a new 1, high wall as close as possible to the precast wall – face bricks to match the existing walls and common bricks to be used behind the face bricks. 4) To remove the existing paver blocks at the proposed new position of the spa - bath - to lay the above blocks elsewhere as required by the owner. 5) To lay a level mm thick 25mpa concrete slab on top of BRC mesch – size of slab to accommodate the spa-bath. The edges of the slab are not to protrude more than mm from the edges of the spa – bath.
