Everything you need to know about electric fence installation
Electric fences can be dangerous and must meet certain requirements to be considered safe.
Main bed; 1x 2,4x2,1 sliding (with 1x 0,6x 1,4 2x top hung side wind), 2x Bedrms; 2x 1,8x 1,8 (with 2x top hung to side half each. remainder fixed) Lounge/dining; Stoep sliding 1x2,5x2,1 (no side panel) 1x 1,8x1,8 (with 2x top hung side openers) 1x 0,9x0,65 (top hung opener) Kitchen; 1x 1,5x0,9 (middle fixed 2x side top hung openers) Flat; 1x 2,1x 2,1 Sliding with side light 1x 0,6x1,5 with 2x t/h openers) Kitchenette; 1x1,8x0,9 with (2x t/h openers to sides) Room; 1x1,8x1,5 with (2x t/h openers) Bath; 1x0,9x0,9 (with 2x t/h openers) 3x toilets; 3x 0,5x0,9 (t/h openers)
One razor wire diameter height (estimate 0,45m) by 9 slabs (13,5m) on east end vibracrete wall and 7 slabs (10,5m) on back vibracrete wall and another 9 slabs (13,5m) on west end vibracrete wall, totalling to 37,5m in length. Need to supply galvanised fixture brackets, onto each concrete upright post, as well.
I already have a clearview fence installed and I am looking for a barbed razor wire fence for the top of the clearview fence. I have an approximate length but I am not percent sure if that length is correct. This is quite urgent as I am looking for the fence to be installed by the end of this month.
40 years ago we built a new office block but using wooden bay windows from an old Parktown mining magnate's house which was being demolished. At the time we restored the wood and repaired all the lead glass windows, however, over the years, the treatment we have been using has obviously not been any good and they are now in desperate need of repair or replacement. Please call me to discuss the problem and give us idea on the practicality of repairing or replacing these windows and possible costs. This involves a bay window frame, 8 windows and 8 fanlights. Thank you
I have a degrees sea view on my patio and I do not want to block the ocean views at all. I would therefore like folding windows in the front of the patio and sliding windows on the side. I am not sure exactly how many windows I will need as I am not sure about the sizes of the windows - I would need someone to advise me on that.
Barbed wire (in rolls) to be affixed/secured to retaining structure ''wall'' in order to prevent intruders climbing retaining structure and gaining access to the property. So lengths of razor wire to be affixed to retaining structure/wall in order to prevent intruders from climbing up the structure/wall. Also required in possibly a new fence will razor wire for a small section adjacent to the retaining structure/wall.
Good day. Can I kindly request a quote. I want to close my patio with either sliding doors or stackable doors depending on affordability. Main door = 6m wide X 2.5m high. Second opening = 1.7m wide X 2.5m high Third opening = 1.5m wide X 2.5m There are two existing sliding doors which I'd like to remove and reuse if possible, their measurements are as follows; 2.4m wide X 2.1m high 1.8m wide X 2.1m high I understand that the final quote will be based on final measurements but I'm seeking an estimate for now. Please quote me and advise with regards to alternative options as I am not fixed with heights. If the 2.1m heights are more feasible, then I'll be happy to install block windows above the doors. The two sides of the patio do not need to be accessible.
The measurements (4 options) I need for the sliding doors are: 3m (L) x 4.5m (w) left and 4.5m (w) 2.8m (L) x 4.5m (w) left x 4.5m (w) right 3m (L) x 4m (w) left x 4m (w) right 2.8m (L) x 4m (w) left x 4m (w)right Please note that the sliding doors will have a pocket in the wall where they stack into when opened. The floor track preferably recessed. The measurements are for doors that meet at a corner 90 degree opening. They can stack separately on either side.
contractor that will be able to remove the existing fence and install a new Steel Palisade fence at the Tsheesebe Primary School in Waterberg District Municipality 3. STEEL PALISADE FENCE AND ACCESSORIES SPECIFICATIONS 3.1. Installation of Steel Palisade Fencing Panels: 1.8 x 3m above ground level. 3.2. Fence bearers: 40 x 40 x 2m angle iron. These are to be placed mm from top of paling and mm from bottom of paling. (mm from ground level). These are to be welded flash with the back of the post. 3.3. Palings “Devil Fork” 21 palings per panel. 30 x 30 x 2mm steel angle iron paling 1.8m high. Paling to be inserted and firmly welded to the bearers at mm centres to be centre. Top of the paling to provide a “Devil Fork” effect and bottom will have a dove tail. 3.4. Installation of 2.4m high (76 x 76 x2 mm) Posts: 76 x 76 x 2mm steel square tubing with closing pyramid caps on top. Post must be 2.4m high and mm will be planted into concrete footing to Engineer’s design. 3.5. Installation of Palisade Gates for Pedestrian and Sliding Gate 3.5.1. Sliding Gate: 5 m wide x 1.8 m high. 40 x 40 x 2 mm 4 m wide x 1.8 m high. 40 x 40 x 2 mm Post to be founded in a concrete footing x x deep. Concrete strength to be 20Mpa (minimum) at 28 days. 3.5.2. Pedestrian gate: 1.2 m wide x 1.8 m high. 40 x 40 x 2 mm 3.5.3. Painting: Clean surface and allow to dry completely. Remove all Flux, Rust, Grease and loose material before painting. All joints must be smoothed. Apply one coat Primer for steel (red oxide) and apply one coat universal undercoat and one coat Gloss Enamel (Traffic Green as specified by the LPDE) No brush painting. 3.5.4. The School has perimeter of metres N.B. the tenderer must price for Installation Labour Only, Including the concrete footing; the fence will be supplied by the fabricators.
Good morning Can you please send me a quote for 4 x 2.4M x 3 M x 20 PALES PER 3 METER /SPIKES=SPEAR 30 X 30 COLDROLL ANGLE panels 1 x 2.4M x 1 M Panels 6 x 3M x 76x76 x 1.6 POST 1 x 0.9 x76x38 Rectangular Tube 1.6 Pedestrian Gate And nut and bolt for mounted all panels mounted to the post Area will be 4M x 3M Am looking for your reply