I have security gates at my home in Pretoria that are very secure. They are heavy steel gates with three levers - one at the top, the middle and the bottom of the gate. I am planning on building a new home in Ballito soon and want to install the same kind of gates. I am looking to have this done sometime in May.
We have a building that is accommodation for about 8 tenants. We are in need of an electrical COC for the building and for someone to ensure that the building is compliant. Every room (8 rooms) has its own DP box and we need to know how the charges will work - per room or one final cost. This is a bit of an emergency and we are looking to have someone come in tomorrow.
I recently installed a jojo tank where the builder placed the pipes underneath a concrete slab but the conrete ended up in the pipes thus blocking it. I would like to relay a small portion of the pipe which directly comes out of the jojo tank and also lift the pump by 30cm. We will have to use a angle grinder to get the pump out.
Good day, I am looking for technicians who can repair Gate Motor or other issues with the front gate. The complex is located in Burger Street. I need service providers who can be available on-call when the gate stops working. Kindly contact me with your details and if you are available after hours and what are you charges. This will help us to contact you immediately if we need some assistance with the gate. Thank You
I have install a solar system and wiring and solar panels was installed by guys that have solar installation experience, but did it privately. Kodak 5kw off grid inverter mks iii, 12 x watt Longi panels and all wires in 6 mm solar flex plus 6mm earth cable.DB has 4 x 20amp fuses, fuse for each string, DP DC surge devise and 32 amp DC breaker. Looking for a coc please
I would like a black metal frame gate with fibre cement panels that go vertically that are also black. Attached is an image for the gate. Note that you cannot see through the gate and that is how I would like it. The gate needs to be 3.5 meters wide and 2 metres tall. I would like the gate to come with all the security measures needed to make sure someone does not try break in.
We have a rumbling sound from what we think is air in water pipes in the ceiling that occurs regularly. This has been an ongoing problem for approximately two months. We have had four plumber call outs (two plumbers). Bathroom tap washers and toilet rubbers have been replaced. Pipes in the roof have been secured. Finally, a ' Hammer Arrestor to the Cold Tap' has been installed. All to no effect. There doesn’t seem to be a solution. The rumbling even sometimes occurs in the middle of the night. Our geyser is on the front wall of the garage. About two months ago we had the geyser moved to a side wall in the garage as we were advised that it was to close to the electricity board and an inverter we had installed. I am not sure whether this could be the problem.
I bought a house that I have to move in. I doubt wether the stability of its electrical connections as the appliances such as air conditioners and built-in radio were ripped off their mountings. There's power on the building and all other equipment like sliding gates,pool pumps,.Stove and lights in the house are working. I require information to ensure that there isn't any loose strands of open ended live wires that may electrocute or set the house alight.
My wooden garden gate has perished and has always been too heavy for its frame. It is in direct sunlight all day and exposed to rain so I need advice on material. I think the frame is still ok, but may need to be reinforced into the wall. The dims of the gate itself are 80cm x cm. Photos attached. I can use the existing lock but the slot would need to be cut out. I can use the existing handles. The colour is a dark brown according to estate colours. It does not need to be completely solid; it can be slotted. I can stain it providing I am given advice as to which primer and stain should be used, dependant on material of the gate. The finished item would need to be hung/lock fitted. I am not looking for a high-end product, but certainly one that would last.
This job is to replace an existing wooden gate that has perished. Pictures are attached. Measurements of the gate itself are 79.5cm x cm to the frame. The frame needs to be replaced too. I would need the existing handle and lock need to be transferred onto the new gate and the whole gate and frame installed. The gate need not be identical to the existing one.
