There is a hole in the bottom timber section of double garage door. My husband has taken a look and the wood does not seem to be rotten. We need someone to offer some advice and let us know whether repairs are even possible and how much it cost. The garage door would be at my son's house in Fourways.
I have security gates at my home in Pretoria that are very secure. They are heavy steel gates with three levers - one at the top, the middle and the bottom of the gate. I am planning on building a new home in Ballito soon and want to install the same kind of gates. I am looking to have this done sometime in May.
Main bed; 1x 2,4x2,1 sliding (with 1x 0,6x 1,4 2x top hung side wind), 2x Bedrms; 2x 1,8x 1,8 (with 2x top hung to side half each. remainder fixed) Lounge/dining; Stoep sliding 1x2,5x2,1 (no side panel) 1x 1,8x1,8 (with 2x top hung side openers) 1x 0,9x0,65 (top hung opener) Kitchen; 1x 1,5x0,9 (middle fixed 2x side top hung openers) Flat; 1x 2,1x 2,1 Sliding with side light 1x 0,6x1,5 with 2x t/h openers) Kitchenette; 1x1,8x0,9 with (2x t/h openers to sides) Room; 1x1,8x1,5 with (2x t/h openers) Bath; 1x0,9x0,9 (with 2x t/h openers) 3x toilets; 3x 0,5x0,9 (t/h openers)
Good day, I am looking for technicians who can repair Gate Motor or other issues with the front gate. The complex is located in Burger Street. I need service providers who can be available on-call when the gate stops working. Kindly contact me with your details and if you are available after hours and what are you charges. This will help us to contact you immediately if we need some assistance with the gate. Thank You
I would like a black metal frame gate with fibre cement panels that go vertically that are also black. Attached is an image for the gate. Note that you cannot see through the gate and that is how I would like it. The gate needs to be 3.5 meters wide and 2 metres tall. I would like the gate to come with all the security measures needed to make sure someone does not try break in.
1 Standard Double Sectional Automated lift door with draughtproofing. The existing Double is of the 40 raised panel type single up and over and will remain in place until all new brickwork is completed 3 mtrs forward of existing door and new door to be fitted before removal of the old door. This is for security reasons. This installation/removal is subject to planning approval and completion of new brickwork and roofing not earlier than September/October time.
40 years ago we built a new office block but using wooden bay windows from an old Parktown mining magnate's house which was being demolished. At the time we restored the wood and repaired all the lead glass windows, however, over the years, the treatment we have been using has obviously not been any good and they are now in desperate need of repair or replacement. Please call me to discuss the problem and give us idea on the practicality of repairing or replacing these windows and possible costs. This involves a bay window frame, 8 windows and 8 fanlights. Thank you
My wooden garden gate has perished and has always been too heavy for its frame. It is in direct sunlight all day and exposed to rain so I need advice on material. I think the frame is still ok, but may need to be reinforced into the wall. The dims of the gate itself are 80cm x cm. Photos attached. I can use the existing lock but the slot would need to be cut out. I can use the existing handles. The colour is a dark brown according to estate colours. It does not need to be completely solid; it can be slotted. I can stain it providing I am given advice as to which primer and stain should be used, dependant on material of the gate. The finished item would need to be hung/lock fitted. I am not looking for a high-end product, but certainly one that would last.
I have a degrees sea view on my patio and I do not want to block the ocean views at all. I would therefore like folding windows in the front of the patio and sliding windows on the side. I am not sure exactly how many windows I will need as I am not sure about the sizes of the windows - I would need someone to advise me on that.
This job is to replace an existing wooden gate that has perished. Pictures are attached. Measurements of the gate itself are 79.5cm x cm to the frame. The frame needs to be replaced too. I would need the existing handle and lock need to be transferred onto the new gate and the whole gate and frame installed. The gate need not be identical to the existing one.
