I would like to remove the bath and install a walk in show. Replace basin and toilet and retile the floor and walls. Install a vanity and towel rail. Window needs to be reduced and new windows installed. I already have the tiles needed. You can call or email me. I am quite busy and not always able to answer calls.
Hi We have some old Astro that is in storage that we would like to install in our school gym facility. The floor space is roughly 6m wide and 25m in length. We have an old carpet there currently that would need to be ripped out and replaced with the turf. We possibly would require a general cleaning of the turf if it is something you are able to provide. Please could you let me know
1. Roof currently Asbestos, which needs to be removed. 2. Knotty pine ceiling to be removed 2. Rafters to be replaced with new 3. Tiles to be installed 4. New facia boards to be install with new gutters and down pipes (4 off) 4. New celling installation 5. Roof to be painted including the new facia boards
1 Standard Double Sectional Automated lift door with draughtproofing. The existing Double is of the 40 raised panel type single up and over and will remain in place until all new brickwork is completed 3 mtrs forward of existing door and new door to be fitted before removal of the old door. This is for security reasons. This installation/removal is subject to planning approval and completion of new brickwork and roofing not earlier than September/October time.
We have a rumbling sound from what we think is air in water pipes in the ceiling that occurs regularly. This has been an ongoing problem for approximately two months. We have had four plumber call outs (two plumbers). Bathroom tap washers and toilet rubbers have been replaced. Pipes in the roof have been secured. Finally, a ' Hammer Arrestor to the Cold Tap' has been installed. All to no effect. There doesn’t seem to be a solution. The rumbling even sometimes occurs in the middle of the night. Our geyser is on the front wall of the garage. About two months ago we had the geyser moved to a side wall in the garage as we were advised that it was to close to the electricity board and an inverter we had installed. I am not sure whether this could be the problem.
There are masonite ceiling boards beneath the roof overhang around the outside of house. The brandering and supports for theses boards is old / rotten / missing and the boards are starting to come loose They need to be reattached and the edges sealed with silicon please. I am happy to Whatsapp pictures of the temporary repairs that I have done if this will help.
is a walled estate established for over 20 years it has currently got onsite guards 2 day 2 night patrolling access control by guards and call in verification of guests or contractors We are looking at improving off site monitoring / UFG tag or similar to allow owners access and 24 /hr monitoring with at least one guard day and night
The roof was recently painted and the winter has damaged some of the roof sheets. The roof is leaking in 3 areas. I would like the roof to be checked and any issues sorted. I have an old roof. The builder has advised me it is either asbestos or fibre cement. I have some water proofing that needs to be done.
6 seven meter metal sheets. The rain has completely ruined my roof and I need 6 metal sheets of 7 meters in size each. I only need the supply and I am willing to collect the materials myself as well. Please get back to me asap as there is a lot of rain coming soon and I need to get this sorted urgently.
My wooden garden gate has perished and has always been too heavy for its frame. It is in direct sunlight all day and exposed to rain so I need advice on material. I think the frame is still ok, but may need to be reinforced into the wall. The dims of the gate itself are 80cm x cm. Photos attached. I can use the existing lock but the slot would need to be cut out. I can use the existing handles. The colour is a dark brown according to estate colours. It does not need to be completely solid; it can be slotted. I can stain it providing I am given advice as to which primer and stain should be used, dependant on material of the gate. The finished item would need to be hung/lock fitted. I am not looking for a high-end product, but certainly one that would last.