We have a building that is accommodation for about 8 tenants. We are in need of an electrical COC for the building and for someone to ensure that the building is compliant. Every room (8 rooms) has its own DP box and we need to know how the charges will work - per room or one final cost. This is a bit of an emergency and we are looking to have someone come in tomorrow.
Good day, I am looking for technicians who can repair Gate Motor or other issues with the front gate. The complex is located in Burger Street. I need service providers who can be available on-call when the gate stops working. Kindly contact me with your details and if you are available after hours and what are you charges. This will help us to contact you immediately if we need some assistance with the gate. Thank You
I have install a solar system and wiring and solar panels was installed by guys that have solar installation experience, but did it privately. Kodak 5kw off grid inverter mks iii, 12 x watt Longi panels and all wires in 6 mm solar flex plus 6mm earth cable.DB has 4 x 20amp fuses, fuse for each string, DP DC surge devise and 32 amp DC breaker. Looking for a coc please
I would like a black metal frame gate with fibre cement panels that go vertically that are also black. Attached is an image for the gate. Note that you cannot see through the gate and that is how I would like it. The gate needs to be 3.5 meters wide and 2 metres tall. I would like the gate to come with all the security measures needed to make sure someone does not try break in.
I bought a house that I have to move in. I doubt wether the stability of its electrical connections as the appliances such as air conditioners and built-in radio were ripped off their mountings. There's power on the building and all other equipment like sliding gates,pool pumps,.Stove and lights in the house are working. I require information to ensure that there isn't any loose strands of open ended live wires that may electrocute or set the house alight.
My wooden garden gate has perished and has always been too heavy for its frame. It is in direct sunlight all day and exposed to rain so I need advice on material. I think the frame is still ok, but may need to be reinforced into the wall. The dims of the gate itself are 80cm x cm. Photos attached. I can use the existing lock but the slot would need to be cut out. I can use the existing handles. The colour is a dark brown according to estate colours. It does not need to be completely solid; it can be slotted. I can stain it providing I am given advice as to which primer and stain should be used, dependant on material of the gate. The finished item would need to be hung/lock fitted. I am not looking for a high-end product, but certainly one that would last.
This job is to replace an existing wooden gate that has perished. Pictures are attached. Measurements of the gate itself are 79.5cm x cm to the frame. The frame needs to be replaced too. I would need the existing handle and lock need to be transferred onto the new gate and the whole gate and frame installed. The gate need not be identical to the existing one.
26× wall sockets points, 13× wall switch points, 1× geyser point and bonding,1× island stove isolator point, 1× distribution board, 1× daynight switch, 1× chandelier, 2× exterior waterproof sockets, 4× sat/tv points, 6× ceiling light, 1× florescent light, 1× gate motor point, 29× down lights and 1× supply entry box
One 6,4 meter gate. More or less One 2.7 meter. More or less. The two gates must meet. The long gate must be in front of the garage doors. Then other gate can be pushed open . We have a caravan that must be able to pass through the small gate. The attachment between the two gates must be able to go down when taking out the caravan.
Move an existing db board in a house To a position 6m away so a wall can be broken down So cut metal conduit in the ceiling extend the existing 2.5cm and 16mm cables by 6m Put in trunking and reroute to new position Mount new plastic db box Move all breakers earth leakage etc from old board to new board
