Claim it for free and start getting requests from customers in your area.
Claim profile for free
1. SCOPE This specification covers the following: m of electric fence and 5 gates (a) Clearing and grubbing of fence route where necessary (b) The installation of 1.8m high – 16 lines barbed lines free standing electric fence fully galvenised. (c) Installation of 3 x sliding gates motorised and 1 x double swing gates, 4 pedestrian swing gates (d) The requirements for existing gates wiring for the Boundary fencing i will share project bill of quantity and scope
• The Clearview fencing height must be increased from 2.0m to 2.2m. • The posts must be at least 2.4m high to allow for the installation of electric fencing. • Please ensure the revised quotation includes the updated fencing panels, posts, and gate specifications accordingly. • High Security Clearview Fence – m • Clearview 76 x 12.7 Aperture, 3.00mm x 4.00mm Diameter • 3 x V Bends, Powder Coated Black • Clearview Sliding Gate & Track • Delivery to Lydenburg
Installation of an electric fence mounted on top of the entire installed Clear-View fencing, including installation of the electric fence over the 2 vehicular gates and 1 pedestrian gate. The supply, deliver and install all required components, including energizers, brackets, cabling, and warning signage, ensuring full compliance with applicable safety and electrical regulations. The system must be thoroughly tested, commissioned, and handed over in a fully operational condition.
Security fence mm high above ground level, formed of 50 x 50 x 2,5mm hot dip galvanised mesh fence including mm diameter razor wire flatwrap with three strands 4mm galvanised straining wires complete six strands galvanised high tensile straining wires with minimum diameter of 4mm, threaded through holes drilled in posts, spaced at mm centres. Binding wires shall be galvanised mild steel wire with a diameter of 4mm, fixed to 50 x 2mm diameter mild steel pipe intermediate post mm high above ground level and mm below ground level cast into x x mm high concrete base as detailed in (Drawing no. -MFB--RS)
On three sides of the boundary it's a 1.8m precast fence (the electric fence will be installed on top of the precast fence. On the front part of the property it's 1.8 m palisade fence (the electric fence will be installed on top of the fence) There's two 5m sliding palisade gates at the front of the facility and there has to be an electric fence too as well.
Fence perimeter: 60m Panel shall be of mm width and mm in heigh Panel aperture size Centre shall 76.2mm x12.12.7mm Panel shall be fixed to post over 48line wire using 8 x double bolt comb clamps and 8 x single bolt clamps using 24 x Anti Vandal bolt Panel and fixtures shall be galvanized A mm high toughened steel Shark Tooth Spikes with Anti Vandal Bolts A mm high Ripper Blame Smart Razor Wire Flat Wrap The panel shall be reinforced with 4x 50mm deep V formation horizontal recessed bands (rigidity) Panel shall be fixed to post over 48line wire using 8 x double bolt comb clamps and 8 x single bolt clamps using 24 x Anti Vandal bolt
Good day, I am seeking a quotation for the supply and installation of a black Clearview fence with the following specifications: Height: 1.2 meters Length: ±80 meters Finish: Black (powder-coated) Scope: Full supply and installation (all materials to be provided by the service provider) Please ensure your quotation includes: All materials (panels, posts, brackets, fasteners, etc.) Labour and installation costs Any groundwork or preparation required Lead time for supply and completion Warranty details Should a site visit be required for inspection or accurate measurements, please do not hesitate to contact me to arrange a suitable time. I look forward to your quotation.
MATERIALS REQUIRED FOR 10 HECTARE FENCE Fence Specifications: - Approximate fence length: 1, metres - Fence height: 2.5 metres - Treated wooden poles throughout - Galvanized diamond mesh fencing - Galvanized barbed wire - One galvanized steel motor gate - All poles to be concreted into the ground Materials Required: 1. Treated Wooden Poles - x treated wooden line poles (3.5m length) - 12 x treated wooden corner/straining poles (3.5m length) 2. Droppers - x treated wooden droppers 3. Diamond Mesh - 1, metres galvanized diamond mesh, 2.4m high 4. Galvanized Barbed Wire - 4, metres galvanized barbed wire (3 strands above mesh) 5. Tension Wire - 5, metres galvanized high-tensile tension wire 6. Gate - 1 x galvanized steel double-leaf motor gate (4m wide) - Hinges and gate fittings - Chain and heavy-duty padlock 7. Concrete - Sufficient concrete for all line poles, corner poles and gate posts 8. Accessories - Galvanized fencing staples - Wire strainers/tensioners - Binding wire - Mesh joining clips and ties - Any other fittings required for a complete installation Please provide separate pricing for: - Supply only - Supply and installation - Transport to site - VAT (if applicable)
Please provide me with your latest catalogue and best quote for clear view fencing of linear meters, with mm height, 1 x double access gate and 2 x pedestrian gates. My prospect sent me a long list stating that they require: a) Certificate of compliance for materials and coatings b) Drawings for gates, and that All steel should be of good commercial quality, galvanized materials. All pipes shall be galvanized (one piece without joints). Furnish moisture-proof caps for all posts. Zinc coating shall be smooth and essentially free from lumps, globs, or points. Miscellaneous material shall be marine fusion bond coated. Post shall be 2.7m long Taper Locking Post, with a width of 85mm - tapering to 45mm with a depth of 85mm. Post shall include ‘Locking Recess Mechanism’ to secure panel edge. Post shall be sealed with a UV stabilized polymer cap. Post finish shall be marine fusion bond coated. Panel shall be of 3,m width and 2.1m in height. Panel aperture size (centres) shall be 76.2mm x 12.7mm. The panel shall be reinforced with 4 x 50mm deep ‘V’ formation horizontal recessed bands (rigidity) Panel shall have 2 x 70° flanges along sides (internal fixtures - all fixtures shall be on the inside of fence line) Panel shall have 2 x 30° flanges along top and toe (integrated rigid angle). Topping should be Marine fusion bond. A mm high toughened steel Castle spike shall be affixed to panel edge, internally at mm intervals using Anti- vandal bolts. A mm high toughened steel Spear spike shall be affixed to panel edge, internally at mm intervals using Anti vandal bolts. Spike finish shall be marine fusion bond coated. TECHNICAL SPECIFICATIONS – PREMIUM HIGH SECURITY WELDED MESH FENCING The fencing system shall be a premium-level, anti-climb welded mesh fencing system meeting the following minimum specifications. 4.1 Fence Height, minimum: mm 4.2 Mesh Aperture (Premium Configuration) of 12.7mm x 76mm OR 12.7mm x mm. The narrow 12.7mm horizontal spacing is required to provide enhanced anti-climb protection. 4.3 Wire Mesh Thickness, manufactured from high tensile steel wire with 3.0mm vertical x 4.0mm horizontal configuration OR 4.0mm vertical x 4.0mm horizontal 4.4 Standard Panel Width of approximately mm, mm OR mm. Panels when installed are to achieve a total length of approximately linear metres. 4.5 Fence Posts shall: * Be square hollow section steel * Minimum 60mm x 60mm x 2mm thickness * Embedded minimum mm into concrete * Spaced at maximum 2.5m centres * Secured with tamper-resistant fasteners 4.6 All components shall have the following Corrosion Protection: * Hot-dip galvanised * Suitable for coastal environmental exposure * Free from defects 4.7 Gates shall be: * 1 x Double access gate * 2 x Pedestrian gate Gates shall: * Be constructed using the same premium mesh configuration * Have reinforced perimeter framing * Include heavy-duty hinges and locking systems * Be installed on reinforced gate posts set in 20MPa concrete.
Requirements: Increase the overall security height by mm above the existing wall. Preferred Option: Install steel posts securely bolted to the top of the concrete wall. Fit two horizontal runs of flat razor wire between the posts. Alternative Option: Install steel Y-brackets bolted to the top of the wall. Fit mm diameter concertina (circular) razor wire within the Y-brackets. Note: The attached image is provided only as a general example of the type of installation I am looking for. My preference is a solution that maintains a clearer, less obstructed appearance, ideally using flat razor wire rather than the circular concertina style, provided it achieves the required mm security height.
