What kind of permissions do I need for my electric fence, and where to get them?
Electrical fences are dangerous, so you need to obtain permission before installing them. What are they? Where do you get them?
Hi. Trust you are well. I require a quote on a carport for the porch area as indicated in the photos. Area approximate size about 4m x 5m. I stay in a complex so estatically it needs to comply with the attached already installed at another unit. (just the 3 grey borders around the edges). Down pipe for water is also a requirement. Thank you
Good day, hope all is well. We are trying to find a company that would be able to provide a drawn up plan to redo a carport's roofing and a patio area with a supported quotation to show how much it would work out if one were to go ahead with the plan post-approval. Would you be able to assist with such a project?
We require a quotation for a fixed-roof carport, with, preferrably translucent carbon-fibre roof sheeting, for 2 cars. Alternatively, please provide us with a quotation of a shadeport, covering 2 cars. We are not yet sure when such a project would start as one has to get used to a missing large, pine tree which had fulfilled the above requirements. ( protection and shade )
Could I get a quote to put up an IBR Car single port and a quote to put up a single n aluminium car port so I can compare the costs. I need the person to come and see me as I live in a complex and the car port I want to put up myst look like all the others here. I have the architects measurements to work on.
Please qoute me on supply and installation of palisade fence: • Steel Posts: Supply and delivery of hor deep galvanised steel posts, 2.60m long 75x75x2mm with xx3mm welded bottom plate. Units. • Steel Posts: Supply and delivery of hot deep galvanised steel posts, 2.60m long xx2mm with xx3mm welded bottom plate. 2 Units • Supply and delivery of panel made 3m long 25x25x3mm vertical hot deep galvanised angle irons. 38x25x5mm top and bottom angle iron. Angle irons to be welded with 6mm fillet welds on the top, middle and bottom horizontal angle irons before galvanizing and installation.
It is more of a shade similar to a carport. It is for my back yard. plus-minus 6m long by 3,5m wide. I am basically looking at covering the space between the two washing poles. The length between the poles is 7.7m – so 8m. The width is between 3.5 to 4m. Basically a carport structure – see examples further below. Not too sure but the sheets must let light through for clothing on the line.
Good day I need drain jet wash done on Thursday (if possible). mm pipe, approx 50m. Floor drain in shop. To grease trap then from there to municipal connection. Kindly mail quote to the above mail address a.s.a.p. If you need any additional information please contact me. Kind Regards, SHORTY
Installation of new additional sewer line as per building plan to main sewer connection and Reroute part of existing sewer line to main sewer connection. 2. Installation of one new heat pump for 2 geysers including: - Relocating 1 existing geyser - installing a new 2nd geyser 3. New installation as per building plan of: 3/4 inch water supply pipes from geyser to points and drainage from points to sewer line for 2 new built bathrooms, 3 existing bathrooms and new built kitchen, and installation of new sanitary fittings 4. Installation of new mentis drain on driveway in front of double garage
9.3m long x 5.3m wide awning. Steel support members must be galvanized with white powder coat. Chromodek sheeting in white. One corner may be supported by exterior walls of house. All other corners require supports. A midspan support one side may be provided by the external walls of house. A freestanding mid-span support will be acceptable. 4 freestanding supports are envisaged.
I need a carport that can accommodate 2 cars, dimensions 7m (width) x 6 m (depth) x 3m (entry height) . It will be free standing, i.e. no attachments to any buildings, all four sides should be secured to the ground. The structure must be made from galvanised steel. The net should additionally cover 3 of the four sides to form an enclosed structure (only the entry point should be open) The carport needs to be removable and must be able to be resurrected at a new location at a later stage. Please provide a quote that specifies the following components separately: (1) Frame structure, (2) Net, (3) Assembly.