What kind of fence offers the most protection?
There are a number of criteria you should look at when deciding which fence would provide you with the most protection against burglars.
Corner posts shall have 12mm diameter hole drilled in the centre for earthing purposes, mesh wire 20mx20m should only be galvanised not hdg. Gates 2xsmall gates 1.5mx3m. 1 main gate5.2x3m. Gates to have spearheaded pales prodruding at the top by mm. Horizontal rails shall be 40x40x5mm angle iron section. Finish of steel palisade to be hot dipped galvanised hdg to sabs and sans specs Sliding gate and swing gate.
REQURE THE MANUFACTURE AND INSTALLATION OF: 1.Galvanised Steel Sliding Gate 6.m long x 1.m high . Should include Wheelbase : mm x 50mm x 1.6mm tubing Wheels ; mm Wheels in casings Gate should have spears(spikes) on top of it. 2. Galvanized steel panel railings to fit on top of a low wall and in between concrete columns with the railings having the following dimensions 3.m long x 1.m high x 1 panel 3.m long x 1.m high x 1 panel 2.m long x 1.m high x 1 panel 2.m long x 1.m high x 1 panel 1.m long x 1.m high x 1 panel Five panels required in total Railings should have spears (spikes on top of it) I have uploaded a picture of the sort of thing. I am looking for. 3. Galvanised Steel Pedestrian Gate 0.m wide x 1.m high
1. mm X 2,5mm X 3m high Corner posts (6 off) With base plate of mm xmm 2. Straining Posts of (mm X2,5mm X 3m High - with caps and mm X mm base plate(4 off) 3.diamond Mesh 50mmX50mmX2,5mm X2,5M High (m) (1off) 4. 3,4m Double leave gate (opening of 4,2m wide)( steel tubing 2,5mmX 48mm). (1off) 5.pedestrian gate (2,5m High) 1m opening 6.Razor wire m
The Contractor shall be required to prevent access to the site by any unauthorised personnel. He shall, as a minimum, supply and erect a suitable temporary fence along all unprotected boundaries of the site. The fence shall be at least 2,0 m high and of such nature that it will exclude adults, children or animals. The fence shall be provided with a lockable vehicle entrance gate, to secure the site after working hours. 6m swing gate.
There are also two gates, 2 by 1.2 meters and 4 by 2 meters. The larger gate must be in two equal sections. both can swing on hinges and lock with a bolt and padlock, and one bolt in the ground in case of the large gate. I'm going to cut the brick pillars down so they are the same height as the wall, so the bottom of the fence will always be same level.
Basic Wire Fence - ( Boundary of Sub-division). Can be wire mesh or square (As in Bonnox type Fencing). Wooden Poles with minimum number of droppers. 1 Leg of 29.5 M, 2nd Leg of 44.0 M (Drive Way) Light Weight Gate ALSO required 4.00 M X 1.8 M same material as fence. Installation required ASAP with Payment in Cash on completion. Light weight gate.
I have an area of 9m x 7.75 m on top of my concrete roof Garage. Proper submitted drwgs to municipality and approval to be done Attaches to a wall for 4.5m on one side. White Chromodeck sheeting and the spacings between the purlins to be maximum of 1.5metres Gutter to be extended to the ground appox 5.5m down Would like a second quote for a 5 metres by 4 metres carport.
We require a palisade fence to be installed on our property. This use to be a driveway gate but we replaced the gate with a wooden fence. We now wish to install a palisade fence on the inside of our property for added protection. There are two solid facebrick pillars on each side to attach the fence.
The canopy structure for walkways shall be designed to include portal frames, purlins, and metal sheet and supported on a reinforced concrete pad footings. All steel works shall be bolted or welded. Structural members of the covered walkway shall be adequately braced and connected to prevent displacement or distortion of the frame work. The canopy roof shall have adequate slope/bents to allow rain water discharge. Allow for rainwater downpipes. See figure 1 below The canopy structure for walkways shall have an opening of 2.6m wide and constructed to a height of the O&M modular space containers. The contractor shall comply with the National Building Standard and must prepare a complete structural design calculations for canopy members including pad footings. The total walkway is m long
im urgently required to install a one metre high palisade fencing on top of a cement block plastered wall . i need 14 sections of various lengths x 1metre high totalling +- 56 running metres. The top edge of the verticals only need to be a sharp point . Could you kindly quote asap .many thanks. Mark, please contact me as possible